-
ANCHORSEAL 2 is a hybrid of plant-based polymers and wax that protects the ends of green logs and lumber from end checking and splitting. AS2 controls the rate of moisture loss during air drying for hardwood, exotic hardwood decking and softwood. It is a high-performance, economical choice for sealing green wood and fresh cut lumber. ANCHORSEAL 2 is best-in-class for the protection of deck end cuts for exotic hardwood species. When carefully applied to the freshly cut ends of tropical hardwoods, such as ipe, Brazilian cherry, mahogany, teak, cumaru & tigerwood, AS2 prevents up to 90% of end checking, protecting your investment and extending the life of the deck. It is also a preferred end grain sealer of the woodworking industry for wood bowls, turning blanks, cookies & live-edge wood slabs. Features: Prevents up to 90% of end checks and drying splits on logs and freshly cut lumber • Hybrid formula combines wax with natural plant-based polymers • Can be applied to all species of hardwood or softwood • Helps prevent blue stain and sapstain caused by damaging fungi • Water based, non-toxic formula, soap & water clean-up • Available in clear or more than 35 colors • Winterized formulas available Coverage: 100 sq. ft./gallon, depending on application method and wood species. Surface Preparation
- All areas to be coated should be clear of dirt and debris
- Apply ANCHORSEAL 2 using a brush, roller or sprayer until it begins to drip slightly
- For optimal coverage, use a gas engine, electric, air operated or backpack sprayer from U·C Coatings
- If using spray equipment other than those sold by U·C Coatings, use 0.21”/0.55 mm tip or larger
- Logs larger than 24”/60 cm in diameter will require a heavier coating, or two coats must be applied within a 15 minute period
- If applying to the cut ends of deck boards: apply ANCHORSEAL 2 carefully with a thin brush or sponge applicator. To avoid potential staining, do not allow ANCHORSEAL 2 to get on the face of the boards.
- If you need a deck end cut sealer that penetrates below the surface of wood that can be painted or stained over, we recommend SEAL ENDS ONCE (also made by U-C Coatings)
- Clean application equipment using hot soapy water
- Store unused ANCHORSEAL 2 above 50°F/10°C to prevent freezing. Winterized formulas will protect against freeze damage
ANCHORSEAL 2 - The leading log & lumber end grain sealer since 2006. Also widely used for sealing wood bowls, cutting boards, turning blanks and protecting the ends of wood decks.
-
-
-
- Motor: 1 HP DC Permanent Magnet Motor
- Controller: Pulse Width Modulation (PWM)
- Electrical Requirements: 110V-1PH-60HZ
- Recommended Breaker Size: 110V - 15 AMP
- Speed Range High 650 - 3500 RPM
- Speed Range Mid 325 - 1750 RPM
- Speed Range Low 50 - 525 RPM
- Distance Between Centers 15.5”
- Swing Over Bed 12-1/2”
- Swing Over Banjo 9-1/2”
- Max. Outboard Swing 16”
- Spindle Bore 3/8”
- Spindle Taper MT2
- Spindle Thread 1”x 8 TPI (both ends)
- Front Bearing 6006LLU
- Rear Bearing 6005LLU
- Indexing 24 positions w/ Lock
- Drive belt Poly-V Belt 6 Grooves
- Tail stock quill travel 2-1/2”
- Tail stock taper MT2
- Bed Length 29.4”
- Tool Rest Length 6”
- Tool Rest Post Dia. 1”
- Faceplate Dia. 3”
- Certification CSA C/US 256540
- Floor to bed height 6.7” no pads
- Floor to Spindle Center 13” no pads
- Overall Size L29.4” W8.9” H17.4”
- Shipping Dimensions L35.8” W14.6” H20.5”
- Net Weight 118 LBS
- Shipping Weight 125 LBS
-
-
Out of stock
CURRENTY IN STOCK. HOWEVER, DUE TO VOLATILE MARKET CONDITIONS, PLEASE CONFIRM AVAILABILITY PRIOR TO ORDERING. This 25”-wide heavy-duty drum sander is a perfect choice for small businesses and hobbyists that are sanding panels around 3 to 5 hours a day. It’s an economical alternative to a planer. Order this 25 inch drum sander from Baileigh Industrial.- Maximum thickness of 5” and minimum of ¼”.
- Dual 5” sanding drums turns at 1,800 rpm.
- Variable speed conveyor can adjust from 6 to 24 feet per minute.
- 3 hp main motor runs on 220-volt single-phase power.
- Convenient adjustment screw ensures that the sanding drum stays parallel to the conveyor belt.
- Easy-to-access drums allow for convenient sandpaper changes.
- Includes 2 dust ports (4”) that you can hook up to a dust collector to keep your shop air clean and safe.
- 2 drums let you use different abrasives at once: for instance, 120 grit for taking material off, then 220 grit to refine the surface.
- Rigid steel base keeps vibrations down to a minimum. Most competitors can’t match the sheer structural strength of our sanders.
- This heavy-duty sander is covered by a 1-year parts warranty.
- We keep replacement parts in stock for fast shipping from our Wisconsin headquarters.
- You can count on lifetime technical support by phone from our team of experts, all with hands-on machine experience.
-
Out of stock
These 20" diameter 150 grit aluminum oxide sanding discs are sized to fit most common disc sanders and are sold in a 2 pk. These sanding discs are pre-applied with top-quality pressure sensitive adhesive. -
These 20" diameter 120 grit aluminum oxide sanding discs are sized to fit most common disc sanders and are sold in a 2 pk. These sanding discs are pre-applied with top-quality pressure sensitive adhesive. -
Out of stock
These 20" diameter 220 grit aluminum oxide sanding discs are sized to fit most common disc sanders and are sold in a 2 pk. These sanding discs are pre-applied with top-quality pressure sensitive adhesive. -
These 20" diameter 180 grit aluminum oxide sanding discs are sized to fit most common disc sanders and are sold in a 2 pk. These sanding discs are pre-applied with top-quality pressure sensitive adhesive. -
These 20" diameter 100 grit aluminum oxide sanding discs are sized to fit most common disc sanders and are sold in a 2 pk. These sanding discs are pre-applied with top-quality pressure sensitive adhesive. -
These 20" diameter 80 grit aluminum oxide sanding discs are sized to fit most common disc sanders and are sold in a 2 pk. These sanding discs are pre-applied with top-quality pressure sensitive adhesive. -
- Motor size: 5 HP
- Tablesaw type: Cabinet
- Blade size: 10"
- Maximum cutting height @ 90deg: 3"
- Maximum cutting height @ 45deg: 2-1/8"
- Maximum ripping capacity - right: 60"
- Table type: Precision-Ground Cast Iron
- Overall table size: 74" x 27"
- Shipping weight: 550 lbs.
-
Designed with the exacting tolerances your shop demands, the SB1108 South Bend 15" Planer is top of its class in precision workmanship and dependability. The helical cutterhead delivers near mirror-smooth finishes right out of the gate. It consists of four rows of 52 indexable carbide inserts, each angled slightly to produce a shearing action. This shearing action results in less tearout in highly figured woods and quieter operation—and the planed surfaces are far superior to what you'll get with 15" straight-knife or other spiral cutterheads on the market. Other high-end features include a digital table height scale for ultra-precise and consistent thickness adjustments, precision-ground cast-iron tables, and triple belt drive—everything that makes this 15" planer truly live up to the South Bend name. The SB1108 manual was written by our U.S. based Technical Documentation Department and is packed with useful information. South Bend tools come with a 2-year warranty which covers parts and assures the unit is free from factory defects. The South Bend Customer Service and Technical Support Teams are U.S. based. Parts and accessories for the jointer are available online and shipped from the South Bend parts warehouse in Springfield, MO.No more messing around. This will be the last 15" planer you'll ever need to buy.
-
Out of stock
This 20”-widehelical head thickness planer can quickly turn rough lumber into boards with smooth faces. Heavy cast iron and steel constructionkeeps the material steady and supported.- 5 hp motor turns the cutter head at a whopping 5,000 rpm.
- Straight 4-row helical head cutter comes standard.
- Runs on 220-volt single-phase power, so it can work almost anywhere.
- Fully cast iron 20” x 25.75” table with 15” extensions can expand to an impressive 20” x 55.75”.
- 2 speedsallow you to pick what’s right for your project:
- 20 feet per minute when you need to smooth boards in shorter amount of time.
- 16 feet per minute when you want a more refined finish or you’re working with tougher material.
- 8” maximum and .25” minimum cutting height.
- Maximum ⅛” cut depth.
- Handwheel with a scale on the side of the planer lets you precisely adjust the height in seconds.
- Cast iron frame on the top and bottom stabilizes the machine and helps it last longer.
- Magnetic safety switch automatically turns the machine off in case of a power outage or a problem with the current.
- Anti-kickback fingers grip the material so it’s less likely to shoot back out if the blades get jammed.
- Extra-large 5” dust port prevents clogging. You can easily hook up your dust collection system, so your shop stays clean with breathable air.
- Built-in wheels on the base allow you to move the machine around your shop and store it.
- Covered by a 1-year parts warranty.
- Replacement parts are in stock at our Wisconsin warehouse for fast shipping.
- Lifetime technical support by phone means that you can call our team of experienced woodworkers whenever you have questions or need troubleshooting.